12/B, Purana Paltan Line (2nd Floor), Dhaka-1000
-
+880-1819273523
-
9:00 am To 6:00 pm (Saturday To Thursday)
-
Testing and Measurement
Testing and Measurement
Why testing and measurement is required?
Testing and measurement of an equipment helps to increase the shelf life, performance, accuracy and efficiency of the devices. Measurement of electrical parameters such as current, voltage, capacitance, resistance, inductance and impedance etc. are critical to detect faults and defects in the device under test. Test equipment measures these parameters, identifying possible errors and risks in the system that can be corrected for effectiveness and reliability.
Testing helps identify the components that undergo timely degradation due to the device's exposure to external disturbances such as heat, shocks, vibrations and fluctuating environmental conditions. This analysis further helps predict equipment failure and perform calibration before any considerable damage.
How Wellmake Service can help you?
Wellmake is one of the leading & reliable engineering services providing Engineering Consultant’s Firm working in the Energy Sectors of Bangladesh since 2004. We are providing Standard Electrical, Compressed Air, Water and Steam system related assessment/audit Services and Solutions maintaining BNBC, BS, IEC, IEEE, NFPA, ASHRAE.
Thus, it’s our pleasure to let you know that, Wellmake has qualified, skilled and field level experienced Certified Energy Auditors (CEA), Certified Energy Manager (CEM) and Engineers from different discipline. Our way of working and dedication in this field is unparalleled, which drives us generally on top and make you work with us.
Testing and Measurement
Electrical System
Ø Transformer
Ø Switchgera
Ø Generator
Ø Protection System
Ø Electrical Application
Thermal & Steam System
Ø Steam Boiler
Ø Thermal Oil heater/Dryer/Oven
Ø Gas Driven Machinery
Ø Flue Gas Test
Ø Combustion Test
Ø O2 Level
Ø CO2 Level
Ø CO Level
Ø SOx
Ø NOx
Ø H₂S
Ø Relative Humidity
Ø Dry & Wet Blab Test
Ø Exhaust/Flue Temperature Test
Ø Combustion Efficiency Test
Ø Thermal Efficiency Test
Ø Performance Test
Ø Stack Emission Test
Compressed Air System
Ø Compressor Efficiency and Performance
Ø Compressed Air Trap Performance (Moisture Trap)
Motor and Pump System
Ø Motor Efficiency and Performance
Ø Pump Efficiency and Performance
Ø Insulation Resistance
Transformer Test
Ø Visual Inspection
Ø Thermal Imaging
Ø Turns Ratio Test (TRT)
Ø Insulation Resistance (IR) Test
Ø Polarization Index (PI) Test
Ø Oil Breakdown Test
Ø Magnetic Balance Test
Ø Tan Delta Test (Insulation Quality)
Ø Dissolve Gas Analysis
HT Switchgear
Ø General Visual Inspections
Ø Insulators and Barrier Checks
Ø Insulation Resistance Test
Ø Thermal Test
Ø Dielectric Test
Ø Thermography Inspection
Ø Circuit breaker contact resistance test
LT Switchgear
Ø General Visual and Mechanical Inspections
Ø Wiring and Bolted Connection Checks
Ø Insulators and Barrier Checks
Ø Thermography Inspection
Ø Moisture and Corona Inspections
Generator
Ø Gas/Diesel/LPG- Generator
Ø Combustion Test
Ø Stack Emission Test
Protection System Test
ØInsulation Resistance Test
ØEarth Fault Loop Impedance Test
ØEarthing/Grounding Resistance Test
ØResidual Current Device (RCD) Test
Ø Prospective Short Circuit Current (PSC) Test
Ø Protection Relay Test
Ø Protective Device Test (MCB, MCCB, ACB, VCB etc.)
Ø Lightning Arrester Test
Type Testing
Ø Low Voltage Continuity Test
Ø Temperature rises limits
Ø Dielectric properties
Ø Short-circuit resistance
Ø Effectiveness of the protective circuit
Ø Clearances and creepage distances
Ø Mechanical operation
Ø Degree of protection (IP)
Ø Resistance to mechanical impact
Ø Rust resistance
Ø Resistance to damp
Ø Resistance of insulating materials to heat
Ø Fire resistance
Ø Mechanical performance of assemblies and fixings
Electrical Testing
Ø Continuity Test
Ø Polarity Test
Ø Contact Resistance Test
Ø Phase Sequence Test
Ø Insulation resistance test
Ø Soil Resistivity Test
Ø Control Wiring Electrical Tests
Ø Metering Electrical Tests
Ø Instrument Transformers
Ø Circuit Breakers and Switches
Ø Control Power Transfer
Ø Cubicle Heaters
Ø Surge Arresters
Ø Capacitor Bank Test
Ø Battery Test
Ø Automatic Transfer Switch Test
Ø Generator Load Bank Test
Ø Portable Appliance Test
Ø Current Injection Tests
Ø System Function Test
Ø Factory Acceptance Test
Ø Site Acceptance Test
Electrical Appliances
Lighting System
( LED Light, CFL, Florescent Lamp, Flood Light, Solar Light etc.)
Testing Parameter
Ø Lux
Ø Efficiency
Ø Candela
Ø Efficacy
Ø Lumen
Ø Power
Ø Harmonics
Ø THD
Ø Power Factor
Ceiling Fan
Testing Parameter
Ø Power
Ø Harmonics
Ø Power Factor
Ø Rotation (RPM)
Ø CFM/CFH
Water Quality Analysis
Ø Raw Water
Ø Soft Water
Ø Condensate Water
Ø Machine Cooling Water
Ø Hot Water/Machine Cooling Water
Ø Drinking Water
Ø Basin Water
Process Water
Ø ETP Water
Ø Washing Water
Ø Dyeing Water